How to Replace a Kia Sportage Replacement Key

For a number of kia remote key fob models the key comes with an integrated keyless entry system. The key is usually akin to an remote control, and is able to be replaced by a new one purchased from an kia picanto key fob replacement dealer or a locksmith.

Key fobs may stop working for a variety of reasons, such as an empty coin battery, worn buttons, water damage, signal interference and a faulty receiver module. Here are some suggestions to help you get your Kia sportage replacement key working for good.

How to replace a remote key or smartkey

The battery in your Kia's intelligent key will eventually need to be replaced, whether it is a remote key as well as a push-to start key or a normal metal key that doesn't contain a transponder. This is especially true if the car displays a message indicating that the remote or smart key has low battery power.

This is a relatively simple process. To replace the battery in the keyfob, remove your mechanical key from the slit at the back of the fob. Then, you need to pry the cover off. Inside the key fob, there will be an incredibly small screw that holds the battery in place. Take out the old battery by unwinding the screw using a small screwdriver. Install the new battery and close the cut on the key fob.

Test the key fob by pressing the lock/unlock buttons. If the doors unlock and lock as expected, then you're good to go! You can now use the hands-free feature to lock and unlock your Kia whenever your fingers feel cold or you need to run errands around Brandon.

Note: Certain key fobs might need to be programmed (transponder chips or smart keys). This requires a particular programming machine that only the dealer or automotive locksmith can access. Other keys (non-transponder metal keys) do not require programming. If your key needs to be programmed again, you will need to be aware of the number stamped on the tag of the key code and keep it in a secure location.

How do I replace the battery?

If the Kia key fob doesn't respond to pressing the lock or unlock button, it's likely that the battery is low. A low battery may cause other issues, like the check engine light flashing or the engine not turning correctly. Fortunately replacing the key fob battery is a simple DIY project that requires just some basic tools.

Make sure that you shut off your vehicle and shut all doors prior to beginning. Find the small metal or a plastic piece at the bottom of the key fob. Jiggle it until the key is released. The key can be inserted into the driver door handle to unlock your car.

To replace the battery on the key fob, remove the cover on the rear. Make use of a plastic pry tool to loosen the latch that holds the black negative cable. Remove the old battery and then position the new battery in a way that its "+" side is facing you, and the "-", negative side is facing the fob's electrical contacts. Push the new CR2032 battery straight into position without putting too much force on it to avoid damaging or breaking the contacts made of metal.

After installing the new battery then turn the key fob off and on in the ignition until the door locks cycle. You can then test your Kia key fob and see whether it's functioning properly again.

How to replace the smart key?

You can have a standard keyfob or a Smart Key, based on the model of Kia Sportage. The difference between them is that the smart key has an incredibly small key blade hidden within it, whereas the standard fob doesn't. Both key fobs contain batteries that will eventually need to be changed. It's an easy task that takes just two minutes.

Be sure to switch off your kia car keys replacement (look at these guys) and sit on a flat well-lit and well-lit area before you begin. Keep in mind that there are tiny pieces inside the fob that can fall out if you are not cautious.

The small release button is located on the lower backside. It could be a circular or rectangular slot. After pressing this button mechanical key blade, it will come out and you will be able to open the key fob.

Once you have the key fob opened then you can take off the old battery and replace it. The new battery should be a CR-2032, and can be bought online or from your local auto parts store. Once you're done, your key fob will allow you to lock, unlock, and start your vehicle even if it's not running.

How do you replace the mechanical key?

The Kia keyfob is an excellent convenience, allowing us to lock or unlock our car by pressing the button. But, as with all devices, it can have problems from time to time. Luckily, there are methods to resolve these issues and keep our key fobs in good working condition for the long run.

One of the most common problems is a dead or dead battery. This could cause the fob to stop working completely or to work intermittently. If this happens then try replacing the battery with a fresh new one.

If this doesn't fix the problem then try using a normal flathead screwdriver to wedge open the fob's plastic casing. Be sure not to damage any internal components, or scratch the plastic. Once the battery is opened, carefully remove the battery you have been using and replace it with a new one.

Close and open the door using the mechanical key. (Every Kia fob comes with a spare kia key mechanical key which will fit into the slot). Test the key fob to ensure it's working as intended. Contact a dealer or locksmith to resolve the problem when the fob still is not working. To avoid locking outs in the future, make sure you get an emergency key that can work on all door and trunk cylinders.