How to Replace the replacement saab 9-3 key Key Battery For the saab 9-3 key replacement, Blogbright says, 9-3

Saab owners have to follow a series of steps that are unique to add a second ignition key. It requires dealer service using an electronic handheld computer called Tech-2. Then a new car key and transponder are required to be purchased and then programmed into the car.

Change your keys regularly to prevent one from deteriorating faster than the other. This will also ensure that your keys remain in top condition.

Replacement Case

Unlike the classic Saab keys of old keys, the new keys have electronic components that make it difficult to create a duplicate. This has made car theft considerably more complicated than it was 20 years ago. It also makes it more expensive to replace keys lost.

Every owner of a Saab 9-3 must have at a minimum two functioning keys. It's expensive to replace a lost key as it requires replacing the CIM module, as well as reprogramming the locking cylinders. Dealers usually charge between $100-$200 for this.

There are ways to cut down on these high costs. Some parts providers will use the code of an extra key to cut a new metal blade at a fraction what the dealer charges. The key must, however, be the same as the original in order to function in your vehicle.

Follow these steps to replace the case. You'll need a flathead screwdriver as well as some patience. With the screwdriver, slowly pry the plastic apart and remove the emergency key from the case. Once the case has been opened, remove all electronics and place them into your new case. Make sure you insert the correct key and badge back inside the case, too.

replacement saab key Battery

The saab 9-3 key programming 9-3 replacement battery is a low-cost component that can be quickly and easily replaced. This YouTube tutorial for DIY Cyclone Cyd will show you how to replace the battery for the remote key fob in only four steps. This tutorial is suitable for any modern saab key fob replacement key fob, though the process may vary slightly.

The first step is to locate the button that will release the backup key on the fob. It's usually just below the Saab logo on the back of the fob. Use a flathead to insert the screwdriver into the small hole in this button. This should be enough to open the case of the fob to allow you to replace the battery.

After the new battery CR1632 is installed, you can reassemble the remote key fob and program it to your car. The entire process should take no more than a half hour at the most. This is a very easy process that doesn't require any special tools.

If you lose your key, the process is slightly more complicated, but it can still be accomplished. The dealer has to verify the VIN of the car, and then request a replacement key blade and TWICE module, both with the correct unique code. The dealer will then have to program the key using MDI, a new software tool.

Key Replacement Fob

The key fob is a device that locks and unlocks your car. It is equipped with a battery inside. They have a limited life span and will eventually fail. It is a common problem with all cars. The good thing is that you can replace the battery in most key fobs without having to replace the entire case. You can purchase fobs replacements on Amazon that have all the electronics already in place, so you'll just pop open the case and replace the batteries that were in the case. It is necessary to remove the emergency key before you replace the batteries. To do this, you need to insert an small screwdriver with a flat head into the slot that is in the middle. The case will split once you rotate the screwdriver around it.

When you're ready to replace your keys, make sure you have spare keys, as this can reduce the total cost by a significant amount. If you have spare keys, you can have the dealer cut the new key and program it to the car, which is much cheaper than replacing the whole key fob.

It is possible to add another key to your vehicle in the event that you don't have one, but it requires an extensive amount of research and work. The cost for adding a second key is several hundred dollars and it also requires programming of the car's computer. Professionals can accomplish this however, it's a costly option.

Replacement Ignition

The modern SAAB 9-3 is an alarm system that is more sophisticated that is based on a key code. This means that when you lose your sole working key, replacing it with another key can be extremely expensive because the car needs to have a specific computer module installed, and it must also be programmed to accept a new key. The majority of locksmiths aren't able to do this, and even dealers can charge several hundred dollars to program the new key!

Dealers will charge you a high price to replace your car computer (also known as the CIM or SAAB twice) when you lose your sole working key. Instead, we can reprogram the EEPROM in your current car computer to prepare it to accept a second key, and save you over 50% of what you'd have to pay at a dealership.

If you have owned a 9-3 from SAAB for many years you're aware that the ignition keys are not very durable. They can get extremely sticky, and the buttons are known to be removed from them from time to time, so you should consider purchasing a new one if yours isn't working properly. The good news is that replacing the ignition key isn't as difficult as it sounds, and it can be done fairly quickly with the appropriate tools.