Reasons Your Fiat 500 Key Fob Won't Work

A key fob for the fiat 500 replacement key cost 500 is a great way to unlock the doors and start the car. However, there are numerous reasons why the fob won't be working. This includes a dead coin-battery, water damage, issues with the receiver module, and interference.

This listing is for an NEW replacement fiat punto key Flip Key Remote - look-alike Ilco brand that needs to be professionally programmed by a local automotive locksmith (click here for Locksmith Search). It comes with lock, unlock and trunk buttons.

Dead Coin Battery

The most frequent reason that your 500 key fob won't function is an inactive battery. Modern key fobs only have a limited range of operation and must be within a few inches of your vehicle to work. If you're far away from your vehicle and press the key fob button the car won't respond, and will display an "Key Fob Not Detected" message in the instrument cluster.

If this occurs If this happens, replace the battery in the coin-cell (Part Number CR2032) by a brand new one from a reputable brand like Panasonic Duracell or Energizer. You can usually find them in your local hardware store or on the internet.

After you've replaced the battery in the coin cell You can test it by standing next to your Fiat 500 and pressing the buttons. The parking lights should flash and the key fob should operate the lock and unlock switch.

If your key fob does not work after replacing the battery, there might be water damage that is preventing it from communicating with the module inside your vehicle. Water damage can happen in many ways, such as simply splashing or submerging your key fob in saltwater at the beach. If you suspect your fob has been exposed to water, try putting it in a dry rice bag to pull the moisture out. If this doesn't work, you will need to have the fob reset by an auto locksmith or a dealer.

Water Damage

Water damage can happen if you immerse the fob into the ocean or wash it locked keys in car boot fiat punto locked keys in fiat 500 In fiat key replacement cost 500, Www.Cuzconetworks.Co.Kr, a washer. Saltwater can cause the circuit board to short and eventually die. In the event that you let your fob get wet, it's not an ideal choice but if you drop it into a cup of water or fail to remove it from your pants pocket before running the washing machine and you don't have a chance, don't give in.

First take the battery off the fob. Before replacing the battery, clean the electronic chip using isopropyl or another similar product. Next test the fob to verify if it is working. If the key isn't working, it may need to be reset. This is usually handled by an auto locksmith or dealer.

If the key is more recent and hasn't been programmed to your vehicle It is likely that it needs to be replaced completely. A professional automotive locksmith can carry out this simple task. The locksmith will need the key to be cut to match your vehicle's ignition. They'll also have to program the fob into your vehicle's system. This is a low-cost and fast process that can be completed on the same day.

Receiver Module Issues

Your 500 key fob may be inoperable because it's out of range. The remote's range is of 30 feet. Therefore, if you are too far from your car it won't be able to respond to your commands. You can easily fix this by moving the remote closer to your vehicle until it responds.

If your fob won't work after replacing the coin battery, also known as a "button", "watch" or "button" It could be a problem with the internal circuit board. Reprogramming the fob usually resolves the issue. The instructions are available for the majority of vehicles on YouTube or in the owner's manual.

You may need to replace the metal retaining clips that hold the battery of your coin in place. If they become loose, it can stop your coin battery from sitting properly and cause your remote to malfunction.

In rare instances, the fob might be out of the vehicle's sync because due to hardware or software issues. This can cause a major problem, but you can often fix this by visiting an auto locksmith to have them reprogram your fob for you. In some instances they might need to install the software again in your body control module, too.

Interference

Interference can also cause the key fob not to receive or transmit the signal. This is possible when the key fob is close to the radio transmitter (cell phones or radar detectors) or any other source of electromagnetic radiation. The key fob might not function due to a bad connection to the buttons or water damage, or damage to the internal chips.

If the key fob has suddenly stopped working, out of the blue, or after trying everything you can do at home to fix it e.g. It could be a defective 500 receiver module If you've tried replacing it with a battery, reprogramming, and using a spare key fob. The receiver module, which is located under the dashboard, receives radio frequency signals from your key fob. It converts the signals into electronic commands, which are then processed by the vehicle.

There's a simple method to reset the 500's in-board system including the keyfob. Disconnect the battery for 15 minutes, removing first the negative cable, then the positive cable. Reconnect the battery. This will clear any residual electricity, and restart the car's computer. This could help you get your key fob to work again. If the issue continues, you should seek out an expert technician. They will be able to determine the root of any problems.