double glazing window repairs Glazing Door Lock Repairs

Have you noticed that your uPVC window or door mechanism deteriorated? Perhaps the door or window handles don't meet up properly or are difficult to use.

You'll be wasting energy if your double-glazed doors don't perform as they should. This also increases the likelihood of burglaries. Owen the Locksmith can fix your door lock for an affordable cost.

Snapped Key

It can be quite frustrating when a key is snapped inside a lock. It could also be a security risk since the door might not lock and could leave you vulnerable to burglars. There are a few quick fixes you can try to repair the issue and get your door working again.

Be sure to remain calm. If you panic and begin doing a lot of fumbling around, you might just end up pushing the broken piece of the key further into the lock, which could make the situation even more difficult.

Next spray WD-40 or a different penetrating oil into the lock to make the broken piece to slide out more easily. You can also use a screwdriver to help break pieces that could be hindering the flow. If you're fortunate enough to have a bit of the key sticking out it, you can make use of a paperclip, or any other metal object with a thin surface to grab it and remove it. Both methods work, but you must be careful not to push the broken key piece further into the keyway.

Some paperclips have grooved edges that can serve as a hook extractor, and some jigsaw blades are also suitable for this purpose. If you don't have any of these, you can bend a hook with needle-nosed pliers. Finally, a pair of tweezers can be used to grasp and pull out the last part of the broken key.

If you are unable to remove the broken piece of key Use a lock deicer. It is available in most hardware stores and is used to freeze any moisture present inside the lock.

If none of these solutions work, it may be time to call a locksmith. Fitlocks experts can fix problems such as broken handles or broken keys with uPVC locks and door mechanisms. They can also alter the double glazed windows repair glazing door mechanisms to ensure that they are easier to use. Book a double glazing repair with us online or give us a phone call to discuss your requirements.

Broken Cylinder

A broken cylinder can pose an extremely risky security issue. It's fortunately a simple repair for an expert locksmith to complete. To fix the cylinder, a locksmith will need to tap it. They can do this using the hammer or any other tool, but the most efficient way is to use a long match or a piece of wire. Then, position the match's end or wire in the keyway. After that, the locksmith will hit the lock to break it open. This is better than using a hammer, which can damage the lock.

The most frequent cause of cracks in the cylinder head is overheating. This can happen when the cylinder block and head are made of different metals, like cast iron and aluminium. Different metals can heat up and cool off at different rates. This can cause localized hotspots to expand faster than the rest of the cylinder.

Corrosion can be a cause of fractures in cylinders. If the cylinder head as well as the block of the cylinder are not properly maintained, it can result in corrosion or rust and cause them to expand at a greater rates than they ought to. As time passes, this may cause cracks.

If your uPVC window or door lock is stiff or requires a lot of pressure to turn, this can be caused by many things. This issue could result from a defective locking mechanism or misalignment, or a worn-out handle.

This is a straightforward and affordable fix that the majority of double glazed repairs glazing owners can accomplish. A professional locksmith can usually solve this issue within an hour of arriving at the property. Depending on your needs they can change the locking mechanism, change the window handles, and also change the gearboxes. A professional locksmith will be able to provide you with a recommendation of the most cost-effective solution for your home. They may recommend upgrading to 3 Star TS007 Euro Cylinders that provide an additional layer of protection against burglars. It's a small price to pay for the peace of mind that comes with knowing your uPVC doors are safe.

Broken Handle

It's not a surprise that window handle locks can break. They are equipped with complex mechanisms that become less effective over time. It isn't easy to determine the reason behind a broken window handle lock and fix it correctly.

If the issue is related to the locking mechanism inside or the latch, repairing double glazing windows your broken handle will increase your uPVC double glazing window repair glazing door's security and help you stop drafts. If you do not repair or replace your handle can be very costly and may harm the door's frame as well as lock and frame, so it's worth spending the time to do it correctly.

Screwdriver: With the window open, loosen the screw holding the handle. The screw should be located on the inside of the backplate, usually hidden by an eye-catching cap to conceal it for aesthetic purposes. Be sure not to lose any internal components within the handle, for example the levers or plates on either side of the spindle. Keep them in the same order so that it is simpler to replace them in the event of a need.

Then, turn the handle until it's 90 degrees towards the window frame. Then, loosen the screw on the back of the handle that fixes it to the internal spindle by using another screwdriver. Once this is loose, you should be able to pull the handle off and pull out the broken spindle. Replace it with a new spindle, ensuring that it's the same length (you can find them online or at hardware stores). Securely screw it into place. Be careful not to overtighten because this could damage the handle or the window frame.

Ensure the new handle is correctly fitted Close the window and test the handle. It should operate smoothly and you'll be able open your window once more.

While you're working on the handle, don't forget to check your uPVC windows are shut properly. If they're not, you could experience damp and draughts inside your home, as in addition to compromising the energy efficiency of your home. A local window company, like Core Sash Windows, will be capable of adjusting the hinges on your window frames so they are able to shut properly.

Broken Spindle

It is more common for the spindle to break rather than the handle. This is especially frequent in uPVC tilt and turn windows. These types of windows require a handle that acts as a locking mechanism within the frame of the window. The handle is attached to a central rod which in turn activates cams that resemble mushrooms, which locks are inserted into the window frame. If the dead latch mechanism does not open when the handle has been turned, it is likely the spindle is damaged. This could be a frustrating issue.

Luckily there are steps that can be taken to remedy this situation. A skilled locksmith can quickly and efficiently fix this problem. They can disassemble the window handle by using a tool that can remove the wheel portion of the mechanism where the spindle goes. This is done without causing any damage to the handle or causing other damage to the window frame.

After the wheel has been removed, the technician can inspect the spindle to determine what has caused it to break. This involves breaking the spindle into its constituent parts and carefully recording their general condition as well as any specific areas of wear or damage. The process is performed in a clean room by highly skilled technicians.

The next step is to clean the damaged spindle, this assists in removing any dirt or other debris that could be hindering its normal functioning. Following this the spindle could be repaired or replaced. If it's being replaced, the technician can take an identical dowel size to the one used in the first and drill mating holes in both pieces of the spindle. This will ensure that the spindle fits perfectly with the handle.

If the damaged spindle is beyond repair, it may be necessary to replace it completely. Home centres sell generic replacements. However, if the style of your window is unusual then you will need to contact a wood worker or cabinet maker who can duplicate the exact model for you. Once the spindle has been installed, it is connected to the handle. Place the screw holes on the handle with the existing screws in the frame. Once the new handle is in place, you'll be able to operate your uPVC window.