How to Change a Subaru Spare Key

If you have lost your Subaru car key, call a locksmith. Locksmiths usually can cut you a key cheaper than the dealer.

Subaru car keys are generally either smart "push-to-start" fob remote keys or basic metal keys. The Fob keys will need to have its chip modified.

Keyless Entry System

The key fob can be used to lock and unlock your Subaru remotely. It also opens the trunk of your car or the lift gate. These remotes make use of a keypad in your car to connect to your vehicle's computer.

Some models of Subaru come with a lesser-known feature called PIN Code Access. This lets you make a unique sequence of numbers to start and open your car. Read the owner's manual to learn how to use this feature if you have a Subaru Forester, Outback Crosstrek, WRX STI or Impreza.

If your keys stop working, there's a good chance that the battery in the key fob is dead. You can check the battery life of your key fob using the portable tester or multimeter you can find in your garage.

The next step is to take the circuit board that controls the transmitter from the key fob to examine it. The board will contain one or two sets of 8-digit numbers, so note down the first set so that you are able to recall it later. After you've completed that you can put the key fob back together and you'll be ready to begin programming it at home. This procedure differs based on the year and model of your car. However, it's usually easy enough to do yourself.

Key Fobs

Subaru impreza key Fob replacement's latest models come with key fobs that not only unlock doors, but also turn on lights, lock the gas cap, and even start the car. This feature is especially useful if encountered yourself at the gas station and your car won't even start because the battery inside the key fob has failed.

It doesn't matter if your Subaru is new or old, it's likely that the key fob is able to be replaced with minimal difficulty. It's important that you remember that newer models with the highest level of technological sophistication could require an appointment at the dealership. With a little time and effort, you can get your replacement key fob ready to go at home.

Begin by looking at the circuit board of the transmitter in your key fob (instructions for opening the case should be provided in the owner's guide). There should be one or two serial numbers of 8 numbers each. Keep the first series of numbers handy for later reference.

Then, get into the driver's seat. Close all doors. Turn the key to start your vehicle before turning off after 10 turns. Press the lock button on your key fob, then open the door. This will confirm that your doors are functioning correctly. Then close the door, and take the key out of the ignition. The chime should be heard from your vehicle once more, signalling that the key fob has been programmed.

Ignition System

If your Subaru keys aren't working as they ought to, it could be due to the fact that the battery is dead. If you know how, you could replace the battery in your key fob yourself. A replacement battery is cheap and easy to locate. If your key fob doesn't respond to your commands, it might be another issue. To get a spare, it's best to visit an authorized dealer. They'll ensure that the key is genuine Subaru key that's covered by warranty. It will also be programmed to your vehicle. This is a lot simpler and safer than buying an aftermarket one from a retailer online.

The dealer is also able to cut keys for you, provided you provide your VIN number and as evidence of ownership. They'll use this information to program the replacement key in order to be recognized by your immobilizer. This is more complex than cutting a new one, and the dealer will generally charge more for this service.

Once the new key is programmed, you'll be able to switch it to your current key. You'll have only five seconds to insert the second key, so it's crucial to keep a working key handy. You can remove the key after the security light been off and you've tested it.

Battery Replacement

Subaru fobs are extremely useful since they can switch on the sunroof and power windows of your car with just a single button press. However, the battery inside your Subaru key fob was not meant to last forever. It will eventually require to be replaced. Fortunately, changing the battery is a straightforward procedure that you can do yourself with the help of this short guide from Capitol Subaru.

To start the process, you'll have to find the small crack in the seam that separates the front and back of your key fob. You can then open the gap using a flathead screwdriver and reveal the small compartment that houses the battery. Insert the new battery and ensure it's facing in the correct direction. Remove the old one. After everything is in place and in place, you can use your new key fob to lock or unlock your vehicle effortlessly!

You should always have a spare set keys, especially if yours is damaged or has gone missing. A new key can easily be purchased at your local dealership for cars or you can have one made by a locksmith. Either way, it's important to get your key fob operating properly as soon as possible to ensure you drive safely!