Reasons Your Fiat 500 key fiat 500 Fob Won't Work

A key fob from fiat punto remote key price 500 makes it simple to open doors and start your vehicle. There are a myriad of reasons why the fob won't be working. It could be due to a dead battery damage to the receiver module, issues, and interfering.

This listing is for an NEW replacement fiat 500x keys nottingham fiat tipo key Flip Key Remote - similar to the Ilco brand that must be professionally programmed by a local locksmith (click here to search for a Locksmith Search). It comes with lock, unlock and trunk buttons.

Dead Coin Battery

A dead battery is the most frequent cause of your 500 key fob not functioning. Modern key fobs have a restricted operating range, and should be within some feet of the car to operate. If you are not within your vehicle and push the keyfob button it will not respond, and display the message "Key Fob Not Detected".

If this happens, simply replace the battery on your coin cell (Part number CR2032) by a new one from a trusted brand such as Panasonic, Duracell, or Energizer. They are typically available in your local hardware store or online.

After you've changed the battery on the coin cell You can test it by standing close to your fiat keys replacement 500 and pressing the buttons. The parking lights will flash and the key fob will operate the lock and unlock switches.

If the key fob doesn't function after replacing the battery, it could be damaged by water, which prevents it from communicating with the receiver module inside your car. Water damage can occur in many ways, including the simple splash or submerging the key fob saltwater at the beach. If you suspect that your fob has been exposed to water, put it in a dry rice bag to pull the moisture out. If this does not work, you'll require your fob to be reset by an auto locksmith or a dealer.

Water Damage

While the fob comes with rubber seals to keep water from the chip's electronic circuit the device, submerging it into the ocean or washing it in a machine could cause water damage. Saltwater poses a particular risk to the fob's circuit board and can cause it to short out and eventually end up dying. It's not good to soak the fob in water, but don't give it up when you accidentally drop it in water or forget to remove it from your pocket.

Remove the battery first. Before replacing the battery clean the electronic chip with isopropyl or a similar product. Check the fob to see if it is working. If the key still doesn't work, it may need to be reset. This is usually handled by an auto locksmith or dealer.

If your key is a bit older and is not programmed for your vehicle it is necessary to replace it completely. This is a simple procedure which can be accomplished by a professional locksmith for automotive use. The locksmith will need to cut the key to match the ignition of your car. They'll also have to program the fob into your vehicle's system. This is a cheap and quick process that could be completed in the same day.

Receiver Module Issues

One of the simplest reasons why your 500 key fob won't be functioning is that it's out of range. The remote's range is of 30 feet, so when you're too far away from your vehicle it won't be able to respond to your commands. You can easily remedy this by moving your remote closer to your vehicle until it responds.

If you've replaced the battery on your coin (commonly known as"button" or "button" or "watch") and your fob doesn't function It could be because of an internal circuit board problem. Reprogramming the fob is usually the solution to this issue. You can find the instructions for most vehicles on YouTube or in the owner's manual.

It may be necessary to replace the clips made of metal that hold the coin batteries in the correct position. If they loose tension, it could hinder the coin battery from being seated properly and could cause your remote to malfunction.

In rare instances the fob might become desync'd with your vehicle due to software issues or hardware issues. You can fix this problem by visiting your local auto-locksmith or dealer to reprogram fiat 500 key fob your key fob. In some cases they might need to reinstall the software in your body control module, too.

Interference

Interference can also cause the key fob to not be able to receive or transmit an signal. This can occur when the keyfob is in close proximity to a radio transmitter such as a cell phone or radar detector. The key fob could not work because of a weak connection with the buttons water damage or damage to the internal chips.

If your key fob suddenly stopped working, or you have tried everything at home to resolve it (e.g. battery replacement, reprogramming and using the spare key fob, it could have a damaged receiver module on your 500. The receiver module, which is located beneath the dashboard, detects radio frequency signals from your key fob. It transforms the signals into electronic commands that are then translated by the vehicle.

There is a straightforward method to reset the 500's onboard system including the keyfob. Disconnect the battery for 15 minutes by taking off first the negative cable, then the positive cable. Reconnect the battery. This will clear any residual electric current, and also restart the car's computer. This could help you get your key fob working again. If the issue continues, you should speak with an expert technician. They can identify the root of any issues.