Replacing uPVC Window Handles

Switching the handles of windows made of upvc is an easy task. The important thing is to make sure that the new handle is a good fit for the spindle that was cut out of the window mechanism.

If you follow the steps below any cockspur handle can fit on most windows. The most important factor is the step height of the handle.

What to Look for

A large portion of windows in the UK come with uPVC handles Over time, they will begin to show signs of wear and wear and tear. The handle on the window may become shaky or difficult to operate when this occurs. Anyone who is proficient working with basic hand tools can complete this relatively simple task.

The first step is to make sure that the handle is securely fixed to the frame of the changing window handles in the open position. The next step is to locate the fixing pins or screws that keep the handle in position. They are usually on the inside of the handle. They can be removed using the screwdriver and pliers.

When the handle is loose It is best to gently pull it away from its hinges. It is then time to find a replacement handle with the same design and size. This can be done online or at a local DIY store, and it should take around five minutes using a screwdriver.

When replacing the handle of a uPVC handle it is essential to consider the step height. This is the distance from the base of the handle to where it rests on the window frame. This is usually a standard measurement, and it is crucial to check the step height of your existing handle before ordering the new one.

There are a variety of sizes based on the type of handle. Inline handles for uPVC windows usually have 31mm lug centres, and there are also handles with cockspur with 43mm centres. Tilt-and-turn handles are commonly found on uPVC windows. They have a specific design that lets the window be tilted to allow for ventilation and then turned to fully open the window.

The most frequent uPVC handle cracks are internal, rather than a breakage from the base. This can make them hard to open and is why it is important to make sure that the replacement handle you purchase has the same spindle length as your existing one.

Remove the handle that was previously used

If the handles on your windows are damaged or not properly fitted, they could cause double-glazed windows to not open or close correctly. They could even become stuck. There are a myriad of reasons for this like general wear and tear or the corrosion of the handle. In these instances it is crucial to find replacement handles made of upvc immediately to avoid further damage and loss of functionality.

When replacing the handles on windows made of upvc it is recommended to remove the old handles from the window. Begin by removing the screw when the handle in closed position. This should reveal another screw, and once it is removed, you can begin to remove the handle. It is recommended to use an electric screwdriver for this since it will make the job easier and faster.

Be aware that screws could be hidden in caps made of plastic. It is recommended to remove the covers with a Stanley knife. After the old handle has been removed, you should then look at the square cut on the base of the handle to ensure that the new window lock handles will work with it. This is important as you'll need to measure the length of the spindle of the old handle to make sure it is in line with the size of the window mechanism and the handle spindle cut out.

The various types of window handles of upvc window handles are: Espag handles, which are equipped with a central screw and can be turned left or right; Cranked handles which have two screws and are typically found on tilt and turn windows made of upvc and Spade handles with an arm with a flat surface and can be put on either side of the window. Once you have found a suitable replacement, it is simple to screw the handle into place and ensuring that the spindle is placed into the lock mechanism. Once this is done the handle should be secured to the window frame, and your new window handles made of upvc must be secure.

Measure the Spindle

If you're replacing a upvc window handle that has slipped off, it's because the spindle holding it in place has become loose or damaged. In some cases this can be fixed with a screw or pin to tighten it. In some cases it might be necessary to replace the handle. There are a variety of handles made of upvc. These include inline espagnolette handles for internal bifold doors - peatix.com, or cockspur handles. They also have tilt and turn handles. Each handle type has its own procedure for installing and replacing the handle.

Before purchasing a replacement handle it is essential to know the size of the handle that is currently in use. This will ensure that the new handle is of the correct size and fits into the window. All handles are sized according to industry standards, making it easy to determine the right size.

To measure the size of your handle, first, take it out of the window by turning it to an open position. You should be able to determine the size of the pin or screw that secures the handle. Then, use a ruler or tape measure to determine the length of the spindle. Once you have the length of your spindle it is possible to purchase a replacement that is exactly the same length.

The step height of a window handle is another factor to take into consideration when purchasing replacements. The step height is the distance from the bottom of the handle to where it is placed on the frame. Typically, this is around 21mm for uPVC windows and 9mm for aluminum. To ensure that the new handle will work the gap, drop something in the gap to determine how far it extends before meeting an obstruction.

Cockspur handles often have different backset heights based on the style of window they're installed in. Inline espag handles have the standard height of 43mm centre to centre (2 fixing points). Cockspur handles have different backsets depending on the type of window they are located in. This is because they have an extension spur that extends from the handle and locks over a cockspur wedge striker plate.

Install the new handle

After you've chosen the new handle, ensure that it is aligned with the holes for screws on the door. Secure it using the screws provided. Install the latch lever the same manner as the main handle if you are also replacing the door handle. Then, you can attach the victorian scroll door handles trim once more to hide the mounting screws.

Tips: To remove a metal head from a wooden wedge, place the handle on the floor so that its wide end is on the floor. Then, you can use an hammer and tap the narrow end. Be careful not to damage the handle or the spindle.