Choosing the Right UPVC Door Handle Replacement

It's easy to replace your upvc handles, but choosing the right handle can be difficult. Modern double-glazed handles are equipped with spring cassettes, whereas older handles don't.

If your upvc handle seems loose and floppy there may be an issue with the internal parts of the multipoint lock. This article will discuss several possible problems and their causes.

Handles that slide or drop

UPVC handles can withstand wear and tear, especially in older properties. A broken spring cassette inside the door lever is the most common reason for a handle that is floppy. This is caused by excessive force and the spindle holding the cassette can be dislocated or round.

The good news is that replacing the door handle made of uPVC is a relatively simple job and can be completed in just a few minutes. The first step is to disassemble the old handle by removing the fixing screws visible on the back of the handle lever plate. Once the handles are removed, you can remove the screws and replace the cassette.

You can find a vast selection of uPVC Door Handles Victorian handles to choose from online, and many of them come in different finishes. Choosing the right finish will determine the length of time your handle will last as well as how it is easy to keep clean. Finishes like Resista Stainless Steel, or PVD are designed to resist corrosion and last for up to 25 years.

After you have selected a colour or design, you can select the type of handle that you need. The most popular types are pad and lever arrangements. Lever pads are typically used to block access by unauthorised persons. They have an inside lever and a paddle out.

The next step is to determine the dimensions of your existing handle and record them. You will need to know the PZ dimension (the distance from the screw hole to the center of the lever) and the length of the handle, and the dimension of the keyhole. You can compare these measurements to the handle size matrix to find the correct replacement.

Broken springs

Over time uPVC door handles are prone to becoming wobbly or loose and occasionally the spring cassette inside may break. The tiny springs bring the handle lever to a horizontal position. without them, doors won't lock properly.

Modern uPVC handles are constructed with these cassettes integrated directly into the backplate. The springs are usually built into older uPVC door mechanisms. This can't be fixed by yourself, but it's worth asking your locksmith to look at as this could be the cause of the sagging or drooping uPVC external door handles and locks handles.

The most common problem with uPVC handles is that they become loose over time. This is usually caused by worn out springs, which are easy to repair. Most often the reason for this is excessive use of the handle, and as a result of that the square spindle in the handle will wear away and the springs will move out of place.

To correct this you will need to open the door and loosen the fixing screws at the back of the handle plate. This can be done by using the Philips screwdriver and once the screws are removed, the handle can be removed and the handle plates pulled apart with care. You can then remove the springs that were in use and replace them with new springs.

Depending on the type of handle you have the distance between the two screws may differ and it is important to know when purchasing an alternative. This measurement is known as the PZ measure. It is recommended that it be taken with a calibrated tape measure in order to be accurate.

After replacing the springs, you should be able to operate the handle with no issues. But, it's recommended to lubricate the internal mechanism to make sure that everything is working just as it should. This will not only ensure that your uPVC doors are as secure as possible but also makes them more comfortable to operate over time too.

Handles that slide around

Handles that slide are caused by a variety of factors. One of the most frequent causes is that the levers of the handle are not aligned with the lock. This is a problem that can occur on uPVC doors and composite doors. However, it is more evident on older bi-fold doors handle as they are made of cheaper materials that don't stand up to the elements.

This issue can be fixed by a professional, who will adjust the handles and ensure that they are in line with the door lock. They'll also inspect the lock to see if there is anything that requires fixing. In many cases, a slight adjustment to the springs of the handle can solve the issue.

Changing your uPVC door handle is easy enough, but you need to measure the existing handles to make sure you have the correct size replacement. You'll need to determine the distance of two screws, the dimensions of the keyhole and lever, as well as the distance between them. You can then use this uPVC handle size guide to determine the appropriate replacement for your home.

After you have made the measurements, take off the existing uPVC handle. It is usually quite easy and requires just a screwdriver get to the screws that are on the inside of the door. Once the screws have been removed, you will need to remove the handle and then install the new handle.

Before you start the work, you should ensure that the door is securely open with a door wedge to stop it from closing during the course of your work. After the handle has been removed you'll be able to get to the inside of the door to fix the issues that cause it to slip.

A handyman from Fantastic Services will be able to help if you don't want to do the work yourself or don't have the skills. They will employ specialist locksmith techniques to unlock the door without causing damage and then replace the faulty handle and make sure that everything is in place and working just as it should.

Gearbox damage

A damaged gearbox may cause the upvc door handle to become stiff or lose function. The lock may also not be able to opened using keys. This can be dangerous and should be addressed as soon as possible. It is crucial to contact a locksmith if you are unable to solve the issue yourself. They have the equipment and knowledge to get the job done right.

The first step is to unhook the handle from its cover plate. This can be done using a screwdriver equipped with flat heads. After removing the handle, you need to remove the middle screw that holds the barrel. After taking out the middle screw, you'll be able to loosen the two screws which are holding the barrel. Then you can pull the barrel from the door. To accomplish this, you'll need someone to hold the door open.

After removing the cylinder you can replace it with a brand new cylinder. Make sure the new cylinder is the exact size as the previous one. Otherwise, you could end with a handle that isn't aligned correctly. This can lead to various issues, including leaks and drips.

Many upvc door handles have slots for adjustment. These slots can be used to tighten or loosen the handle. The slots are typically located on the inside of doors, near the spot where the handle meets with the cylinder. Allen wrenches can be used to tighten the slots of adjustment. After you've made the required adjustments then you can screw the handle back in and put it back in position. Then, you'll be able to test the handle for patio door to make sure that it is working correctly.

The door handle made of upvc that becomes floppy when closed is usually an indication that the spring or gearbox components have broken down. This can cause your multipoint locks made of upvc to fail leaving your door open to intrusion. In this scenario the gearbox made of upvc will require replacement. The cost will range from PS145 to PS280 inclusive of labour.