Replacing uPVC Window Handles

Changing Upvc Window Locking Handles window handles is a simple task. It is crucial to make sure that the new handle fits inside the spindle cutout of the window mechanism.

If the steps listed below are followed properly the cockspur handle will fit most windows. The key is the step height of the handle.

What to Look For

Many of the windows in the UK come with uPVC handles and, over time, they will begin to show signs of wear and tear. If this occurs, the handle may become loose or difficult to operate, which makes it essential to replace it. Anyone who is familiar using a basic hand tool can complete this relatively simple job.

The first step is to make sure the handle is firmly attached to the window frame and in the open position. The next step is to locate the fixing pins or screws that hold the handle in the position it is in. They are usually on the inside of the handle. They can be removed with the screwdriver and pliers.

When the handle has become loose, gently pull it away from its hinges. Then, you will need to find a new handle that is the same size and style. This can be done online or in an area DIY store, and should take around five minutes using a screwdriver.

One important factor to consider when replacing a uPVC window handle is its step height. This is the distance from the base of the handle to the point at which it is placed on the frame of the window. This is a common measurement, and you should verify the step height before ordering an replacement handle.

Depending on the type of handle you have there are various sizes to choose from. Inline handles can be found for uPVC window with centers of 31mm for lugs, while cockspur handles have lug centres of 43mm. Tilt and turn handles are typically found on uPVC windows, and they have a special design that allows the window to be tilted to allow for ventilation, and then turned to open the window fully.

The most frequent breakage in uPVC handles is that they crack internally rather than breaking off from the base section. This can make them hard to open, and it is therefore essential to ensure that the replacement handle you buy has the same length of spindle as the one you have.

Remove the handle that was previously used

A poorly fitted or damaged window handles could cause your double glazed door handles-glazed windows to open and close in a way that isn't correct and may result in them becoming stuck. This can be caused by various factors, such as general wear and tear on the metal handle or corrosion. In these situations, it is vital to replace the upvc window handle as promptly as you can to prevent further damage or loss of function.

One of the first things that you should do when replacing the handles on your windows made of upvc is to remove the old handle from the window. Start by removing the screw when the handle in closed position. This will reveal a screw that once removed, you can then begin to take off the handle itself. It is recommended to make use of an electric screwdriver for this, as it makes the job easier and faster.

It is also worth noting that the screws on the handle could be hidden behind caps made of plastic, so it is recommended to use the Stanley knife to the screw covers and take them off. Once the old handle is removed, you should then take a look at the square cut on the handle's base to ensure that the new window lock handles will work with it. This is important because you will need to measure the length of the spindle on the previous handle to ensure it is in line with the size of the window mechanism and the handle spindle cut out.

There are three types of upvc handles: Espag handles with a central screw that can be turned either left or right, Cranked handles with two screws and Spade handles, which are made of flat arms and can be used on either side of the windows made of upvc. It is simple to replace the handle once you've found one that is suitable. Simply screw it into the frame, and make sure the spindle is properly inserted in the lock mechanism. Once that is done the handle should be secured to the window frame and the replacement upvc window handles should be secure.

Take a measurement of the Spindle

If you're replacing a Upvc window handle that has come off, it is likely because the spindle that holds it in place has become damaged or loose. In some cases, you can tighten the spindle using pins or screws. In other situations, it will need to be replaced entirely. There are a variety of handles made of upvc. There are three types of handles: inline espagnolette cockspur, and tilt-and-turn. Each type has a different method of installing and replacing the handle.

It is crucial to measure the handle before purchasing the replacement. This will ensure that the handle will fit the window properly and will be the right size. All bi-fold doors handles are sized in accordance with industry standards, making it easy to find the correct size.

To determine the size of the handle you must turn the window to the open position. You should be able see the dimensions of the pin or screw that secures the handle. Make use of a ruler or tape measure to determine how long the spindle is. Once you know the length of your spindle it is possible to purchase a replacement of exactly the same length.

The step height of a window handle is also important to take into consideration when you are buying a replacement. The step height is measured from the base to the point where the handle is placed on the frame. This usually is around 21mm or 9mm in aluminium and uPVC. Dropping objects into the gap will allow you to observe how far the handle extends before it comes into contact with an obstruction.

Cockspur handles typically have different backset heights, based on the style of window they're installed in. Inline the espag handle heights range from 43mm from centre to centre (two fixing points). Cockspur handles have different backsets, based on which window design they are in. This is because they have a spur that extends from their handle and locks onto a cockspur wedge hitting plate.

Fit the New Handle

If you've decided to replace the handle, ensure that it is aligned with the screw holes in the door and secure it using the screws supplied. If you're replacing the latch lever, it can be installed in a similar way to the door handle. After that, attach the patio door handle trim once more to hide the mounting screws.

Tips: To remove a metal head from a wooden wedge place the handle on the floor so that its wide end is on the floor. Then, you can use to tap the thin end. Be careful not to scratch the handle or spindle.