Reasons Your fiat 500 key replacement cost 500 Key Fob Won't Work

A key fob from fiat Panda Key 500 makes it easy to open doors and start your car. There are many reasons the key fob might stop working. These include a dead coin battery or water damage, receiver module issues, or interference.

This listing is for a NEW replacement fiat scudo key Flip Key Remote - an exact replica of the Ilco brand that needs to be programmed professionally by a local locksmith (click here for Locksmith Search). It comes with lock, unlock and trunk buttons.

Dead Coin Battery

A dead battery is the main cause of your 500 key fob not working. Modern key fobs offer only a limited range of operation and must be within just a few inches of the vehicle in order to work. If you're not close to your vehicle and you press the key fob button, the car will not respond, and will display a "Key Fob Not Detected" message in the instrument cluster.

If this happens, simply replace the battery in the coin cell (Part number CR2032) with a new one from a reputable brand such as Panasonic, Duracell, or Energizer. They are available at your local hardware store or online.

After you've replaced the coin cell battery, you can test it by standing in front of your fiat key cover 500 and pressing the buttons. The car will blink its parking lights, and the key fob should work the lock and unlock switches.

If your fob's key does not work after replacing the battery, there may be water damage which prevents it from communicating with the module in your vehicle. Water damage can occur through a variety of methods, including an easy splash or submerging the key fob in saltwater at the beach. If you suspect that your fob was exposed to water, put it in a rice bag to draw out the moisture. If that doesn't work your fob will probably need to be reprogrammed by a professional auto locksmith or dealer.

Water Damage

Although the fob is equipped with rubber seals that keep water out of the electronic chip inside it, submerging it in the ocean or washing it in a machine can cause water damage. Saltwater poses a particular risk to the circuit board of the fob which causes it to short out and eventually die. Getting the fob wet is not an ideal choice but if you drop it in the water in a cup or don't remember to remove it from your pants pocket prior to running the washer, don't give up hope.

First, remove the battery. Clean the electronic chip using isopropyl or a similar product and dry it thoroughly before replacing the battery. Next check the fob to test if it works. If the key does not work, it may need to be reprogrammed. This is usually handled by a dealer or professional auto locksmith.

If your key is old and not programmed for your vehicle, you will need to replace it completely. A professional automotive locksmith can carry out this simple task. The locksmith will need to cut the key to match the ignition of your vehicle. They'll also have to reprogram the fob in the system of your car. This is a quick and affordable process that can usually be completed within the same day.

Receiver Module Issues

One of the main reasons your 500 key fob could stop functioning is because it's out of range. The remote has a maximum range of 30 feet. So should you be too far away from your vehicle, it won't respond to your commands. It's easy to remedy this by moving your remote closer to your vehicle until it responds.

If you've replaced the coin battery (commonly known as a "button" or "watch") and your fob doesn't function it could be due to an internal circuit board problem. Reprogramming the fob is usually the solution to the issue. You can find the procedure for most vehicles on YouTube or in the owner's guide.

It is sometimes necessary how to get fiat key code replace the metal clips that hold the coin batteries in their place. If they lose tension they could stop the coin battery from being seated properly and cause your remote to malfunction.

In rare instances, the fob may become desync'd with your vehicle due to software or hardware issues. This can be a major problem, but you can often fix this by visiting a local dealer or auto locksmith to have them reprogram your fob for you. In certain instances, the software may also require reinstallation into your body control modules.

Interference

In addition to a dead battery on a coin The key fob might not be able to transmit or receive an signal due to interference. This could occur if the key fob is in proximity to radio transmitters (cell phones and radar detectors) or any other source of electromagnetic radiation. Other reasons why the key fob could not function include a weak connection to the buttons, damage to the internal chip, or water damage.

If the key fob stopped working one day suddenly, or after trying everything you can do at home to solve it e.g. You could have a malfunctioning 500 receiver module in the event that you've tried replacing the battery, reprogramming, and using an alternative key fob. The receiver module, which is located beneath the dashboard, detects radio frequency signals from your key fob. It then converts them into electronic commands that the vehicle interprets.

There's a simple method to reset the 500's in-board system, including the keyfob. Disconnect the 12 volt battery for approximately 15 minutes by removing the negative cable first then the positive cable. Reconnect the battery. This will erase any remaining electricity, and restart the computer of your spare car key fiat 500. This can help get your key fob working again. If the problem persists you should speak with an expert technician. They'll be able to determine the root of your problems.