Reasons Your fiat key cover 500 Key Fob Won't Work

A key fob for the fiat panda key (just click the up coming internet site) 500 makes it easy to open doors and start your car. However, there are many reasons why the fob may stop working. These include a dead battery or damage where to get a fiat key cut the receiver module, water problems, and interference.

This listing is for a NEW replacement fiat punto key replacement Flip Key Remote that appears similar to the Ilco brand. It needs to be professionally programmed (click here to search for local locksmiths in the automotive industry). It comes with lock, unlock and trunk buttons.

Dead Coin Battery

A dead battery is the main reason for your 500 key fob not working. Key fobs of today have limited operating range and must be within just a few inches of the vehicle to work. If you're far from your vehicle and you push the keyfob button it will not respond and display the message "Key Fob Not Detected".

If this happens, simply replace the battery in the coin cell (Part number CR2032) by a new one from a reputable brand such as Panasonic, Duracell, or Energizer. They are usually available at your local hardware store, or online.

You can test the coin-cell battery by pressing the buttons while you are standing close to your fiat key fobs 500. The car should blink its parking lights, and the key fob should operate the lock and unlock switches.

If the fob's remote doesn't function after replacing the battery, it might have water damage that stops it from communicating with the receiver module in your car. Water damage can occur in a variety of ways, from an accidental splash to submerging the fob in salt water at the beach. If you suspect that your fob has been exposed to water, you can place it in a rice bag to draw out the moisture. If this doesn't work, you will have to get your fob reprogrammed either by an auto locksmith or dealer.

Water Damage

Damage to the water supply can occur if you immerse the fob into the ocean or wash it in a washer. Saltwater can cause the circuit board to short and eventually end up dying. It's not a good idea to let the fob get wet but don't give up if you accidentally drop it in water or forget to take it out of your pocket.

Take the battery off first. Clean the electronic chip using isopropyl or a similar product and then dry it completely before replacing the battery. Check the fob to see if it is functioning. If the key doesn't work, it might need to be changed. This is usually done by an auto locksmith or dealer.

If the key is newer and hasn't been programmed to your car it is likely to need to be replaced completely. A professional locksmith for cars can complete this simple process. The locksmith needs to cut the key to match the ignition of your car. The locksmith will also need to reprogram your fob into the car's system. This is a simple and affordable process that is usually completed the same day.

Receiver Module Issues

One of the simplest reasons your 500 key fob won't be functioning is because it's out of range. The remote usually has 30 feet of range or less and if it's far away from your car it won't respond to your commands. It's easy to remedy this by moving your remote closer to your vehicle until it responds.

If you've replaced the battery on your coin (commonly called a "button" or "watch") and the fob won't work it could be due to an internal circuit board problem. Reprogramming the fob is usually the solution to the issue. You can find the steps for the majority of vehicles on YouTube or in the owner's guide.

It's possible that you need to replace the metal clips that keep the coin battery in place. If they loose tension, it may prevent your battery from sitting properly, causing your remote to malfunction.

In rare cases the fob might become desync'd with your vehicle due to software or hardware issues. This can be a major problem, but you can often fix this by visiting a local dealer or auto locksmith to have them reprogram your fob for you. In some cases, the software may also require reinstallation to your body control modules.

Interference

Interference can also cause the key fob to not receive or transmit a signal. This may happen if the keyfob is in close proximity to a radio transmitter, like a cellphone or radar detector. Other reasons why the key fob could not function may be a lack of connection to the buttons or damage to the internal chip or water damage.

If your key fob suddenly stopped working, or if you have tried everything at home to resolve it (e.g. replacing the battery, reprogramming, and using the spare key fob, you may have a malfunctioning receiver module on your 500. The receiver module, located beneath the dashboard, receives radio frequency signals from your key fob. It transforms the signals into electronic commands that are then read by the vehicle.

There is a straightforward method to reset the 500's in-board system, including the keyfob. Disconnect the battery 12 volt for about 15 minutes by disconnecting the negative cable first then the positive cable. Reconnect the battery. This will erase any remaining electricity, and restart the computer in your car. This can help get your key fob working again. If the problem persists you should speak with an expert certified technician. They will be able to identify the exact cause of issues.