Reasons Your Fiat 500 Key Fob Won't Work

A key fob for fiat key replacement near me 500 replacement key near me (Read Home ) 500 allows you to easily open doors and start your car. There are a myriad of reasons the fob won't work. This includes a dead coin-battery or water damage, issues with the receiver module, and interference.

This listing is for a NEW replacement fiat doblo key Flip Key Remote that appears similar to the Ilco brand. It needs to be professionally programmed (click here to find local locksmiths for your vehicle). This remote includes lock, unlock and trunk buttons.

Dead Coin Battery

The most common reason your 500 key fob doesn't function is due to a dead battery. Key fobs of today have limited operating range and must be within a few inches of the vehicle in order to function. If you're far from your car and push the keyfob button it will not respond and display the message "Key Fob Not Detected".

If this happens, replace the coin-cell battery (Part Number CR2032) with a new battery of a trusted brand such as Panasonic Duracell or Energizer. They can be found in the local hardware store or online.

You can test the battery of your coin-cell by pressing the buttons while standing near your fiat ducato remote key programming 500. The parking lights will flash and the key fob will operate the lock and unlock switch.

If the key fob won't work after replacing the battery, it might be damaged by water, which prevents it from communicating with the receiver module inside your car. Water damage can happen through a variety of methods, including simply splashing or submerging the key fob in saltwater at the beach. If you suspect that your fob was exposed to water, place it in a rice bag to draw out the moisture. If this fails, you'll need to have the fob replaced by an auto locksmith or a dealer.

Water Damage

Water damage can happen if you immerse the fob in the ocean, or wash it in a machine. Saltwater is especially dangerous to the circuit board of the fob that can cause it to short out and eventually end up dying. It's not a good thing to get the fob wet however, but don't give it up even if you accidentally drop the fob in water or forget to remove it from your pocket.

Take the battery off first. Clean the electronic chip using isopropyl or a similar product and dry it thoroughly before replacing the battery. Test the fob next to determine if it's functioning. If the key still doesn't work, it may have to be changed. This is usually handled by an auto locksmith or dealer.

If the key is newer and hasn't been programmed to your vehicle, it will likely need to be replaced completely. This is a simple procedure that can be carried out by a professional automotive locksmith. The locksmith must cut the key to match the ignition of your vehicle. The locksmith will also need to reprogram the fob into the car's system. This is an affordable and fast process that can be completed within the same day.

Receiver Module Issues

One of the main reasons why your 500 key fob could stop working is that it's simply out of range. The remote has a maximum range of 30 feet, which means locked keys in fiat 500 the event that you are far away from your vehicle, it won't respond to your commands. This can be fixed by moving closer to your vehicle until it starts responding.

If your fob isn't working after replacing the battery inside the coin, which is also called a "button", "watch" or "button", it could be a problem with the circuit board inside. Reprogramming the fob usually resolves the issue. There are instructions on how to do this for the majority of automobiles by searching YouTube or looking through the owner's manual.

It may be necessary to replace the metal clips that hold the coin batteries in the correct position. If they lose tension, it could hinder the battery from sitting properly and could cause your remote to malfunction.

In rare cases, the fob may become disconnected from your vehicle because of software or hardware issues. It is possible to fix this issue by visiting your local dealer or auto-locksmith to reprogram your key fob. In certain instances it may be necessary to reinstall the program in your body control module, as well.

Interference

Interference can also cause the key fob to not be able to receive or transmit the signal. This could occur if the keyfob is located in close proximity to a radio transmitter, like a cellphone or radar detector. Other reasons the key fob might not function include a weak connection to the buttons or damage to the internal chip or water damage.

If your key fob suddenly stopped working, or if you have tried everything at home to fix it (e.g. You could have a malfunctioning 500 receiver module If you've tried replacing it with a battery, reprogramming or using an alternative key fob. The receiver module, which is located under the dashboard, detects radio frequency signals from your key fob. It converts the signals into electronic commands which are then translated by the vehicle.

There's a quick and easy way to reset the 500's onboard system including the keyfob. Disconnect the battery for 15 minutes, removing first the negative cable and then the positive cable. Reconnect the battery. This will eliminate any remaining electricity, and restart the computer of your car. This will help you get your key fob to function again. If the problem persists you should consult an expert technician. They will be able to determine the root of your problems.