Peugeot 208 Key Replacement

peugeot 208 key replacement; helpful hints, is best left to auto locksmiths with experience who have the proper equipment and technical knowledge. They can program and create keys quicker and more efficiently than dealerships.

If your key fob stopped locking or unlocking your doors it is likely due to a dead battery in the coin. There are many other reasons for the key to be malfunctioning.

Dead Coin Battery

A dead coin battery can hinder your Peugeot 208 from locking or unlocking and cannot start the engine. If this is the case, you'll need to use the backup starting method that is described in your vehicle's owner manual.

The spark plugs may also be worn out. The spark plugs are responsible for sparking the fuel which starts the engine. However they are limited in their life span. They will eventually break down in the event that they aren't utilized enough.

Luckily, there is an easy solution for this issue. The best option is to measure the voltage of your car battery using a multimeter. If the voltage is lower than 11,5 volts, then it's time to replace it. If the battery is damaged it is crucial to clean its contacts. You can do this by lifting the rubber covers that protect the two terminals on the battery and using wire brushes to clean any corroded components of the battery. Then, you should reconnect the positive and negative pole cables.

Water Damage

If your 208 won't start and the battery isn't empty, you must ensure whether the spark plugs are working. You might find that they are simply too dirty and they don't spark. The spark plugs can be cleaned in an workshop.

peugeot 207 new key cars are equipped with a key with a transponder that is compatible with the immobiliser. This makes sure that only the correct key is able to start the engine. If the chip inside the Peugeot key is damaged, it will not send the proper signal to the vehicle.

Water damage is the most common cause of this problem. This is especially prevalent in colder climates, where the vehicle could have been exposed to rain or snow. In this case, you need to contact a reputable locksmith who will have the required tools and equipment to change the key's programming. They will also have the latest technology and machinery required to create a Peugeot smart key. The process shouldn't take more than 15 minutes.

Faulty Battery Contacts

Peugeot changed from the carbon-encased transponder chips to an entirely new type of chip that incorporates electronic components within circuit boards. The new system works great in its initial state, but the circuit boards deteriorate over time and stop working properly.

This can stop the immobiliser from working, so your vehicle will not start. Contact an Peugeot specialist or a locksmith, if this is the situation.

Another issue that is common is when the battery in the key fob begins to fail, which causes the blade of the key to stop feeding into the lock. A locksmith in your car can replace the battery and cut a new blade for you, this is usually a simple fix.

Faulty Receiver Module

If your Peugeot key fob has stopped working after dropping it on the floor, being exposed to a sudden rain or accidentally washing it, it could be due to a faulty receiver module. The receiver is responsible for sending radio frequency signals to an on-board computer, which is responsible for controlling the centralized locking system of your Peugeot vehicle.

The key fob itself has rubber seals to prevent water from reaching the electronic chip inside. However, prolonged exposure to water can break through these seals, causing damage to the chip. The high salt content of the ocean or pool can cause damage to the key fob if it is submerged.

If your Peugeot spare key fob stops working then you'll have to get the module replaced. This should be done by a peugeot 107 key programming specialist or an expert auto locksmith. In contrast to other vehicles, Peugeot keys are protected by an exclusive immobilizer system that requires the right coding to start the engine. This is why it is imperative that you should only trust a Peugeot locksmith to create and program an alternative.

Computer on-board is not working properly

The computer on board of your peugeot key code is responsible for various features in your car, including power windows and airbags. The on-board computer will display an error code when something goes wrong. The code will be stored within the system until the problem is resolved. Usually, this will mean replacing the computer on board.

The most typical reason for the airbag warning light to illuminate is corrosion or loose connections in the sensor. It can be due to wear and tear, ageing, or exposure to moisture and salt. This issue needs to be dealt with as soon as you can, as an airbag that is not functioning could be dangerous in the event in the event of an accident.

If your Peugeot is showing a card detected as not present error, then the key battery inside the key fob could be weak or dead. This will prevent the key fob from transmitting a signal that will disable the standard immobilizer in your vehicle. You can test this by pressing the unlock button on the key fob, then attempting to start your car. If this doesn't work the battery on the key needs to be replaced.