Replacing uPVC Window Handles

It is simple to change the handles on windows made of upvc. It is crucial to ensure that the new handle fits into the spindle cutout in the window mechanism.

If you follow the steps below the handle of any cockspur will fit most windows. The step height of the handle is important.

What to Do You Look For?

A lot of windows in the UK come with uPVC handles, and over time they may begin to show signs of wear and wear and tear. When this happens, the window handle may become loose or difficult to operate, which makes it necessary to replace it. Anyone who is comfortable using a basic hand tool can accomplish this fairly simple job.

The first step is to make sure the handle is securely attached to the window frame and in a position that is open. The next step is to locate the pins or screws that hold the handle in place. They are usually located on the inside of the handle and can be removed with a screwdriver, or pliers.

Once the handle has become loose, gently pull it away from its hinges. The next step is to find a replacement handle of the same style and size. This can be done at an online store or in a DIY store. The process should take only five minutes and a screwdriver.

When replacing the handle on a uPVC handle it is essential to think about the step height. This is the distance from the base of the handle to where it is placed on the frame of the window. This is typically an accepted measurement, however it is important to determine the step height of your existing handle prior to ordering an entirely new one.

Depending on the type of handle you are using, there are different sizes available. Inline handles are available for uPVC windows that have centers of 31mm for lugs, while cockspur handles come with centers of lugs of 43 millimetres. Tilt and turn handles are often found on windows made of uPVC and they come with a unique design that allows windows to be tilted in for ventilation, and then rotated to open the window completely.

The most frequent uPVC handle breakage is internal cracking instead of a break at the base. This makes them difficult to open and is why it is essential to ensure that any replacement handle you purchase has the same length of spindle that your current one.

Remove the old Handle

If your window handles are damaged or incorrectly fitted, they can cause double-glazed windows to not open or close correctly. They may even become stuck. There are a myriad of reasons for this, such as general wear and tear or corrosion of the metal handle. In these instances it is crucial to replace the window handle as quickly as you can in order to avoid further damage or loss of function.

When replacing the handles of windows made of upvc it is recommended to remove the handles that were previously installed from the window. Begin by removing the screw covered when the handle in closed position. Once you have removed the screw, you are able to remove the handle. You can make the process easier by using an electric screwdriver.

It is also worth noting that the screws on the handle could be hidden behind caps made of plastic, so it is recommended to use an Stanley knife to the screw covers and remove them. After the handle has been removed, look at the square cut out at the handle's base to ensure that the new window lock handles are compatible with it. It is crucial to measure the spindle length on the handle that was used and compare it to the dimensions of the window mechanism spindle cutout.

There are three kinds of Upvc handles: Espag handles with a central screw that can be turned right or left and Cranked handles that have two screws, and Spade handles which are made of flat arms and can be used on either side of the window made of upvc. It is easy to replace the handle when you have identified one that is suitable. Just screw it into the frame, and ensure that the spindle is correctly inserted in the lock mechanism. Once you have done this then tighten the handle to the window frame. The replacement upvc handle for double glazed window should now be secure.

Take a measurement of the Spindle

If you're replacing a upvc window handle that has fallen off, it is likely because the spindle that holds it in place has become loose or damaged. In some instances, this could be fixed with a screw or pin to secure it. In other cases it will have to be replaced completely. There are many different kinds of upvc handles. There are three types of handles: inline espagnolette cockspur, and tilt-and-turn. Each type of handle is mounted and replaced in a different way.

It is essential to measure the current handle prior to purchasing an alternative. This will ensure that the handle will fit the window correctly and be the correct size. Fortunately, all handles follow industry standards for sizing, so it's quite easy to locate the correct size.

To determine the size of your handle, first, remove it from the window by turning it to an open position. Then, you should be able to see the size of the screw or pin that is holding it. Then you can use a ruler or tape measure to determine the length of the spindle. Once you have determined the length of the spindle, you can purchase a new one that is exactly the same size.

The step height of a upvc window handle is also a factor to take into consideration when buying an alternative. The step height is measured from the base to the point at which the handle sits on the frame. This is usually around 21mm or 9mm in aluminium door handles and uPVC. Dropping something into the gap will let you see how far the handle extends before it comes into contact with an obstruction.

Cockspur handles can have different backsets, based on the style of window you install them in. Inline espag handle heights are 43mm from the centre to the centre (two fixing points). Cockspur handles have different backsets depending on which window design they are placed in. This is due to the fact that they have a spur that extends from their handle and is locked onto a cockspur wedge hitting plate.

Install the New Handle

When you've picked a new handle, make sure you align it to the screw holes in the door and secure it using the screws provided. Install the latch lever the same manner as the handle that you are replacing when you're replacing the door handle. After that, attach the external door handles euro lock trim in order to conceal the mounting screws and finish the job.

Tip: To remove the metal head from the wedge made of wood, hold the handle so its wider end is resting on the floor. Use a hammer to tap on the thin end of the handle. Be careful not damage the handle or the spindle.