Reasons Your fiat punto key replacement 500 Key Fob Won't Work

A fiat 500 Replacement key cost uk 500 key fob allows you to easily open doors and start your car. However, there are numerous reasons why the fob may stop working. This could be due to a dead coin battery or damaged receiver module, water damage issues, and interference.

This listing is for a NEW replacement fiat 500x key Flip Key Remote - an exact replica of the Ilco brand that must be programmed professionally by a local locksmith (click here for Locksmith Search). It includes trunk, lock and unlock buttons.

Dead Coin Battery

A dead battery is the most frequent reason for your 500 key fob being inoperative. Key fobs of today have a limited range of operation and must be within a few inches of your vehicle to work. If you're far away from your vehicle, and you press the key fob button the car won't be able to respond, and will display the "Key Fob Not Detected" message in the instrument cluster.

If this happens, simply replace the battery on your coin cell (Part number CR2032) by a new one from a trusted brand such as Panasonic, Duracell, or Energizer. They are available at the local hardware store or online.

After you've changed the battery on the coin cell you can test it by standing near your fiat punto key programming 500 and pressing the buttons. The car will blink its parking lights and the key fob should be able to operate the lock and unlock buttons.

If your key fob does not work after replacing the battery, it may be water damage which prevents it from connecting to the module inside your vehicle. Water damage can happen in many ways, such as a simple splash or submerging your key fob in saltwater at the beach. If you suspect your fob was exposed to water, put it in a dry rice bag to draw the moisture out. If this fails, you'll require your fob to be reprogrammed either by an auto locksmith or a dealer.

Water Damage

Damage to the water supply can occur if you immerse the fob into the ocean, or wash it in a washing machine. Saltwater poses a particular risk to the circuit board of the fob that can cause it to short out and eventually end up dying. It's not a good idea to submerge the fob in water but don't give up when you accidentally drop it in water or fail to take it out of your pants pocket.

Take the battery off first. Clean the electronic chip with isopropyl alcohol or a similar product and then dry it completely before replacing the battery. Next check the fob to test if it works. If the key isn't working, it may have to be programmed again. This is usually handled by an auto locksmith or dealer.

If your key is older and is not programmed for your car You will need to replace it completely. A professional automotive locksmith will be able to complete this process. The locksmith will need the key cut to match the car's ignition. The locksmith will also need to reprogram your fob in the car's system. This is a quick and cost-effective process that is usually completed the same day.

Receiver Module Issues

Your 500 key fob may not function because it's out of range. The remote typically has a range of 30 feet or less, and if it's too far away from your car key cover fiat 500 it won't respond to your commands. You can fix this by moving the remote closer to your vehicle until it responds.

If you've replaced your coin battery (commonly known as"button" or "button" or "watch") and your fob still won't work It could be because of an internal circuit board issue. In most cases, reprogramming the fob will resolve this issue. You can find the instructions for the majority of vehicles on YouTube or in the owner's manual.

It could be necessary to replace the clips made of metal that hold the coin batteries in place. If they loose tension, it could hinder the battery from being properly seated, and this will result in the malfunction of your remote.

In rare instances, the fob may become disconnected from your vehicle because of software or hardware issues. This can cause a major trouble, but you could frequently fix this issue by visiting an auto locksmith to reprogram your fob for you. In some cases it may be necessary to reinstall the software on your body control module as well.

Interference

In addition to a dead coin battery, the key fob may not be receiving or transmitting signals due to interference. This can happen when the key fob is near an electronic radio transmitter (cell phones, radar detectors) or any other source of electromagnetic radiation. The key fob could not function due to a bad connection to the buttons, water damage or damage to the internal chips.

If the key fob been unable to function for a while suddenly and you've tried everything you can at home to resolve it e.g. You may have a faulty 500 receiver module in the event that you've tried replacing the battery, reprogramming it, or using a spare key fob. The receiver module is situated under the dash and is able to pick up the radio frequency signals from the key fob. Then, it converts them into electronic commands that the vehicle interprets.

There is a simple way to reset the 500's on-board system, including the keyfob. Disconnect the battery for 15 minutes by taking off first the negative cable, then the positive cable. Reconnect the battery. This will clear any residual electricity, and allow you to restart the computer of your car. This can help get your key fob working again. If the issue continues, you should consult an expert technician. They will be able to determine the root of any problems.