Reasons Why Your Nissan Qashqai Key Fob Won't Work

The Qashqai has a distinct SUV-like feel due to its larger dimensions. Additionally, the wheel sizes of 19 inches in Ti and ST-L models can be a bit spongy at times. The front tyres could lose grip on rough surfaces, and its CVT can occasionally display wrist-flexing torque steer.

This is typically caused by the battery of a coin that is dead. It is easily replaced in a matter of minutes. Make sure the replacement car key nissan qashqai battery is the same size, voltage and specifications.

Water Damage

Water damage is one of the most frequent causes for the Nissan keyfob to display the "key ID is wrong" message. The key fob comes with rubber seals that protect the electronic chip inside. However, prolonged exposure to moisture could cause it not to function properly. This is typically the case when you've dropped your key fob into the ocean or in a swimming in a pool, but it can also happen if it gets wet from rain or soapy hands.

If your key fob has been exposed to water for an extended time, it may need to be cleaned using isopropyl alcohol or electronic cleaner. It may also need to be sent to an expert for repair or replacement nissan car key.

If your key fob does require replacement the process is easy. Make sure you have the correct multipack (CR2032, 3V). Open the front and rear cases with the flat-head screwdriver. Remove the metal clips, then remove the old battery and replace it. Reassemble the fob and replace the mechanical key. Verify that it is working properly. If it isn't, you'll need to take it to an Nissan dealer or professional auto locksmith to replace the key chip. The chip is not usually damaged by water and isn't too costly.

Dead Coin Battery

Another common reason the reason your Nissan Qashqai key fob might not work is because the battery inside is dead. These batteries last 3 to 5 years, but they can become faulty over time when the fob is dropped often. You can try replacing the battery with a fresh one, but make sure it's the same voltage and size as the original. If you choose to use a different battery it may cause the key to have an incorrect key ID, which will prevent it from pairing with your vehicle.

The best method to replace the battery in a Nissan Qashqai key fob is by prying open the fob with an incredibly small screwdriver with a flat head. Push in the screwdriver in a small notch at the bottom of the fob and turn it around gently to separate the two parts of the key fob. Remove the old CR2025 battery and replace it with a new one, making note of the position of the old one within the fob.

Before you put the new battery into place check to ensure there isn't any water damage or dirt on the terminals. If there how much is a replacement key for nissan qashqai, clean the terminals with a tiny amount of isopropyl alcohol. Also, make sure the pole cables are connected correctly. They must be connected to the negative and positive poles of the battery respectively.

Troubleshooting

If your Nissan Qashqai key fob stops working after exposure to clean tap water or rain, it may be an indication of a chip issue inside. The battery replacement won't fix this, and you'll have to purchase a new key fob. If you dropped the key fob on the ground and it stopped working instantly it is likely because it has damaged the internal chip. You can usually get the key fob to work once again if it is removed and clean the chip using paper towel and isopropyl alcohol and then insert it back into.

A common error that you may notice on the dashboard of your vehicle is "Key ID Incorrect." The car is unable to recognize the key fob and thus won't allow the vehicle to start. This issue can be caused by various ways, including water damage, issues that are undetectable within the key fob circuitry or RFID interference.

The key fob won't work if the 12 volt batteries are not working or provide sufficient electric current. This will affect the remote keyless system and central locking in your nissan car key Qashqai, as well as hindering you from starting the engine using the key fob (if equipped with Intelligent Key). Check the battery in the key fob in case you are in a position to lock or unlock your door by hand. You could also try re-inserting the battery to reset the transmitter.

Reprogramming

If the key fob was not submerged into saltwater it should be able to return to life with a simple rinse of clean water. You can also clean the electronic chip with isopropyl or electronic cleaner. If none of these works, you may need to replace the key fob.

If your Nissan Intelligent Key is still not working, it could be an issue with the connection between it and the car. Start by turning the ignition key but not initiating the vehicle. Continue this process until the hazard light flashes twice. Turn the vehicle off and take away the keys.

Then, you need to open the fob compartment in your vehicle. It is typically located in a door jamb, on the handle for the driver's door or underneath an armrest. Locate the small button labeled "program" and press it. You will hear a sound after the process is completed.

It's time to test your Intelligent Key to the test. Make sure you press all the buttons on the key while you are at a distance from the vehicle. If the lights flash and the horn sound it means the key has successfully connected to the Nissan. You can also test it near the Nissan.