Reasons Your fiat 500x key fob 500 Key Fob Won't Work

A key fob for fiat 500 locked keys in car 500 makes it easy to open doors and start your vehicle. There are a myriad of reasons the fob could stop working. This could be due to a dead battery and water damage, as well as receiver modules issues, and interference.

This listing how much is a new fiat 500 key for an NEW replacement fiat 124 spider key fob not working Flip Key Remote - similar to the Ilco brand that needs to be programmed professionally by a local automotive locksmith (click here to search for a Locksmith Search). It comes with lock, unlock and trunk buttons.

Dead Coin Battery

The most frequent reason why your 500 key fob will not function is due to the battery is dead. Modern key fobs come with a restricted operating range, and should be within only a few feet from the car to operate. If you are further away from your vehicle, and you press the keyfob button, it won't respond and display the message "Key Fob Not Detected".

If this happens, replace the coin cell battery (Part number CR2032) with a brand new one from a trusted brand like Panasonic, Duracell, or Energizer. You can find them at your local hardware store or online.

After you've replaced the coin cell battery It is possible to test it by standing next to your fiat panda key 500 and pressing the buttons. The parking lights will flash and the key fob will operate the lock and unlock switches.

If your key fob isn't working even after replacing the battery, it may be water damage that hinders it from interacting with the module inside your vehicle. Water damage can occur in a variety of ways, from small splashes to submerging the fob salt water at the beach. If you think your fob was exposed to water, place it in a rice bag to draw out the moisture. If this fails, you'll require your fob to be reprogrammed either by an auto locksmith or dealer.

Water Damage

Damage to the water supply can occur if you immerse the fob in the ocean or wash it in a machine. Saltwater is particularly dangerous to the fob's circuit board and can cause it to short out and eventually die. If you get the fob wet, it's not an option but if you accidentally drop it into a cup of water or forget to take it out of your pants pocket before running the washer, don't give up hope.

Remove the battery first. Clean the electronic chip with isopropyl alcohol or another similar product and then dry it completely before replacing the battery. Check the fob again to verify if it's functioning. If the key still doesn't work, it might need to be reset. This is typically handled by a dealer or professional auto locksmith.

If your key is a bit older and has not been programmed for your car then you'll need to replace it completely. This is a simple procedure that can be completed by a professional automotive locksmith. The locksmith needs to cut the key to match the ignition of your vehicle. They will also need to reprogram the fob to the system of your car. This is an affordable and quick procedure that can be completed within the same day.

Receiver Module Issues

The 500 key fob could not function because it's out of range. The remote has a maximum range of 30 feet. Therefore, should you be too far away from your vehicle, it won't respond to your commands. This can be easily fixed by moving closer to your vehicle until it begins responding.

If your fob isn't working after replacing the coin battery, also called a "button", "watch" or "button" It could be a problem with the circuit board inside. Reprogramming your fob can resolve this problem. You can find the instructions on how to get fiat key code to do this on the majority of automobiles by searching YouTube or checking out the owner's manual.

It could be necessary to replace the metal clips that hold the coin batteries in place. If they lose tension, it could prevent your coin battery from being properly seated, causing your remote to malfunction.

In rare cases it is possible that the fob will become disconnected from your vehicle due to software or hardware issues. You can fix this issue by visiting your local auto-locksmith or dealer to reprogram your key fob. In some cases, they may need to install the software again in your body control module too.

Interference

Interference can also cause the key fob to be unable to receive or transmit signals. This may happen if the key fob is in close proximity to a radio transmitter such as a cell phone or radar detector. Other reasons why the key fob might not function include a weak connection to the buttons or the internal chip, or water damage.

If your key fob suddenly stopped working, or you have tried everything at home to fix it (e.g. replacing batteries, reprogramming or using the spare key fob, you might have a damaged receiver module on your 500. The receiver module, located under the dashboard, is able to pick up radio frequency signals from your key fob. It converts the signals into electronic commands which are then interpreted by the vehicle.

Fortunately, there's an easy method to reset every single system on board in your 500 and include the key fob. Disconnect the 12 volt battery for about 15 minutes by disconnecting the negative cable first then the positive cable. Then, reconnect the battery. This will get rid of any remaining electrical charge and restart the car's computers. This can help you the key fob to function again. If the issue persists, you should consult an expert technician. They'll be able identify the root cause of your issues.